This equipment is connected to the service provider through a data circuit-terminating equipment (DCE) device, which is commonly a modem or channel service unit (CSU)/ data service unit (DSU). In a real-world WAN connection, the customer premises equipment (CPE), which is often a router, is the data terminal equipment (DTE).
#Floater df 168a manual serial#
Task 2: Cable the Serial Link between the R1 and R2 Routers. What color is the link status light next to the NIC interface on PC2? _green_ What color is the link status light next to the FastEthernet 0/0 interface on R2? _green_
#Floater df 168a manual Pc#
Because there is no switch between PC2 and the R2 router, a crossover cable is required for a direct link between the PC and the router.
Use a crossover Ethernet cable to connect the FastEthernet 0/0 interface of the R2 router to the NIC of PC2. If the lights do not turn green after a few moments, check that you are using a straightthrough Ethernet cable and that the power is on for the S1 switch and PC1. What color is the link status light next to the NIC interface on PC1? _green_ What color is the link status light next to the FastEthernet 0/2 interface on S1? _green_ If the link status lights are not green, wait a few moments for the link between the two devices to become established. Use a straight-through Ethernet cable to connect the network interface card (NIC) of PC1 to the FastEthernet 0/2 Interface of the S1 switch. What color is the link status light next to the FastEthernet 0/0 interface on R1? _green_ What color is the link status light next to the FastEthernet 0/1 interface on S1? _green_ Step 2: Connect PC1 to the S1 Switch.
Use a straight-through Ethernet cable to connect the FastEthernet 0/0 interface of the R1 router to the FastEthernet 0/1 interface on the R1 switch. Which of the devices in the Topology Diagram require an Ethernet cable between them? _ PC1 to S1, S1 to R1, and R2 to PC2_ Step 1: Connect the R1 Router to the S1 Switch. A simple way to identify the available interfaces on a router is by entering the show ip interface brief command. But you can use any current router in your lab as long as it has the required interfaces as shown in the topology. The output used in this lab is from Cisco 1841 routers. Cable the Ethernet links for a network that is similar to the one in the Topology Diagram. Task 1: Cable the Ethernet Links of the Network. Lab 1.5.1: Cabling a Network and Basic Router Configuration
This document is Cisco Public Information.ĬCNA Exploration Routing Protocols and Concepts: Introduction to Routing and Packet Forwarding However, you may substitute the shorter version, Lab 1.5.2: Basic Router Configuration, if your instructor determines that you are proficient in the essential skills reviewed in this lab.Īll contents are Copyright © 1992–2007 Cisco Systems, Inc. The skills presented in this lab are essential to completing the rest of the labs in this course. You will also learn to save configuration files and capture your configurations to a text file. Scenario (Instructor Note: This lab replaces Lab 1.5.2: Basic Router Configuration and should be used if the student needs extensive review of prior skills.)In this lab activity, you will review previously learned skills including cabling devices, establishing a console connection, and basic IOS command line interface operation and configuration commands. Verify and test configurations using show commands, ping and traceroute. Perform basic IOS command line interface operations. Ĭable devices and establish console connections.Learning Objectives Upon completion of this lab, you will be able to: Lab 1.5.1: Cabling a Network and Basic Router Configuration (Instructor Version) Topology Diagram Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration: Routing Protocols and Concepts course as part of an official Cisco Networking Academy Program. This document is exclusive property of Cisco Systems, Inc.
0 kommentar(er)
